Tools
The toolbox
What it takes to read a bus, forge a frame, probe a chip or capture a radio signal. The well-known public tools, grouped by use, with what each one does.
CAN reading and injection
Read, replay and forge traffic on a bus, from the software side.
can-utils / candump
softwareCaptures and displays, in real time, every frame on a SocketCAN interface. The starting point of any reconnaissance.
can-utils / cansend, cangen
softwareForges and injects a specific frame, or generates a stream of frames to flood the bus or fuzz an ECU.
can-utils / canplayer
softwareReplays a recording of frames verbatim, timestamps included. The canonical tool for the replay attack.
can-utils / cansniffer
softwareGroups frames by identifier and highlights the bytes that change. Ideal for isolating a signal.
SavvyCAN
softwareA cross-platform GUI for capturing, replaying and reverse engineering CAN and CAN-FD frames.
Wireshark
softwareA network analyser with SocketCAN and ISO-TP dissectors to pick a capture apart frame by frame.
python-can
softwareA Python library that drives most CAN interfaces: capture, injection and scripted automation.
Diagnostics and UDS
Talk to the ECUs through the standardised diagnostic services.
Caring Caribou
softwareThe "nmap of CAN": UDS service discovery, identifier scanning, fuzzing and session brute-forcing.
python-udsoncan
softwareA Python implementation of UDS (ISO 14229) for scripting sessions, data read/write and routines.
python-doipclient
softwareA DoIP client (diagnostics over IP/Ethernet) to reach the ECUs of recent vehicles.
Scapy (couches auto)
softwareForges and dissects CAN, ISO-TP, UDS, DoIP and GMLAN from Python, for custom scenarios.
J2534 / pass-thru
hardwareThe standardised interface of OEM tools, often repurposed for flashing and diagnostics.
CAN hardware interfaces
The physical bridge between the PC and the CAN-H / CAN-L pair.
CANtact / CANable
hardwareOpen-source USB-CAN adapters, recognised natively by SocketCAN. The entry level of the lab.
Peak PCAN-USB
hardwareA very widespread professional CAN interface, with stable drivers and broad tooling support.
Kvaser Leaf
hardwareA rugged CAN/CAN-FD interface with a complete API, common in embedded engineering.
Macchina M2
hardwareEmbeddable hardware plugged straight into the OBD-II port, programmable for fieldwork.
Raspberry Pi + chapeau MCP2515
hardwareA low-cost embedded platform for building a standalone CAN bench and scripting in Python.
Radio and wireless
For RF entry points: key fobs, keyless entry, cellular, GNSS.
HackRF One
radioA wideband SDR from 1 MHz to 6 GHz, transmit and receive. Captures and replays key fob signals.
RTL-SDR
radioA very cheap receive-only SDR, for observing and identifying the bands in use.
YARD Stick One
radioA sub-GHz transceiver (300-900 MHz), tailored for remote controls and RF key fobs.
GNU Radio
softwareA signal-processing workbench for assembling custom transmit and receive chains.
Low-level hardware and fault injection
When you open up the ECU and attack the silicon.
ChipWhisperer
hardwareA platform for fault injection (voltage or clock glitching) and side-channel analysis.
JTAGulator
hardwareAutomatically identifies exposed JTAG / SWD debug pins on an unknown board.
Bus Pirate
hardwareA Swiss army knife for talking SPI, I2C and UART to a chip and probing a circuit.
Analyseur logique
hardwareCaptures the digital signals of an internal bus to reverse engineer them offline.
flashrom / programmateur mémoire
hardwareReads and writes an ECU's flash memory, to extract or replace a firmware image.
Simulation and frameworks
Practise without a vehicle, and tool up your campaigns.
ICSim
frameworkOpenGarages' dashboard and CAN traffic simulator, for practising replay without a car.
Metasploit (hwbridge)
frameworkA hardware bridge that lets you drive CAN interfaces from the exploitation framework.
OpenGarages / Car Hacking Village
frameworkResources, test benches and documentation from the car hacking community.
Reference list for learning. None of these tools is run here.